1 p-channel 30 v (d-s) mosfet feature s ? extended v gs ra nge ( 25 v) for adaptor switch applications ? extremely low r ds( on) ? trenchfet ? power mosfet ?100 % r g and uis tested ? typical esd performance: 4000 v (hbm) applications ? adaptor switch, load switch ? power management ? noteb ook computers and portable battery packs notes: a. based on t c = 25 c. b. surface mounted on 1" x 1" fr4 board. c. t = 10 s. d. maximum under steady stat e conditions is 90 c/w. p roduct summary v ds (v) r ds(on) ( ? ) max. i d a q g ( typ.) - 30 0.0065 at v gs = - 10 v - 29 66 nc 0.0082 a t v gs = - 6 v - 23 0.0 112 at v gs = - 4.5 v - 20 absolute maximum ratings (t a = 25 c, unless otherwise noted) p arameter symbol limit unit drain-source voltage v ds - 30 v gate-source v oltage v gs 2 5 continuous drain current (t j = 150 c ) t c = 25 c i d - 25.8 a t c = 70 c - 20.7 t a = 25 c - 17.3 t a = 70 c - 1 3.9 b, c pulsed dr ain current (t = 300 s) i dm - 60 c ontinuous source-drain diode current t c = 25 c i s - 5 .8 b, c t a = 25 c - 2 .6 b, c single pulse a valanche current l = 0.1 mh i as - 40 single pulse a valanche energy e as 80 mj maximum power dissipation t c = 25 c p d 6.9 w t c = 70 c 4.4 t a = 25 c 3.1 b, c t a = 70 c 2 b, c oper ating junction and storage temperature range t j , t st g - 55 to 150 c t hermal resistance ratings p arameter symbol typical maximum unit maximum junction-to-ambient b, d t ? 10 s r thja 33 40 c/w maximum junction-to-foot (drain) steady state r thj f 15 17 1 2 3 4 5 6 7 8 s s s g d d d d 6.15 mm 5.15 mm p owerpak so-8 bottom vie w s g d p-channel mosfe t dt 1 w ww.daysemi.jp
2 no tes: a. pulse test; pulse width ? 300 s, duty cycle ? 2 % b. guaranteed by design, not s ubject to production testing. st resses beyond those listed under ?absolute maximum ratings? ma y cause permanent damage to the device. these are stress rating s only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. s pecifications (t j = 25 c, unless otherwise noted) p arameter symbol test conditions min. typ. max. unit static drain-source breakdo wn voltage v ds v gs = 0 v, i d = - 250 a - 30 v v ds t emperature coefficient ? v ds /t j i d = - 250 a - 24 mv/c v gs( th) t emperature coefficient ? v gs( th) /t j 6 gate-s ource threshold voltage v gs( th) v ds = v gs , i d = - 250 a - 1.2 - 2.8 v gate-source leakage i gss v ds = 0 v , v gs = 25 v 150 a v ds = 0 v , v gs = 20 v 15 zero gate voltage drain current i dss v ds = - 30 v , v gs = 0 v - 1 v ds = - 30 v , v gs = 0 v , t j = 55 c - 10 on-state drain current a i d(on) v ds ?? - 5 v , v gs = - 10 v - 20 a drain-source on-state resistance a r ds( on) v gs ?? - 10 v , i d = - 13 a 0.0054 0.0065 ? v gs ?? - 6 v , i d = - 10 a 0.0068 0.0082 v gs ?? - 4.5 v , i d = - 8 a 0.0093 0.0112 forward transconductance a g fs v ds = - 1 5 v, i d = - 13 a 44 s dy namic b inpu t capacitance c iss v ds = - 15 v , v gs = 0 v , f = 1 mhz 4620 pf output capacitance c os s 880 re verse transfer capacitance c rs s 820 t otal gate charge q g v ds = - 15 v, v gs = - 10 v , i d = - 17.3 a 102 153 nc v ds = - 15 v, v gs = - 5 v , i d = - 17.3 a 66 80 gate-source charge q gs 16 gate- drain charge q gd 28 g ate resistance r g f = 1 mhz 0.3 1.3 2.6 ? tu r n - o n d e l ay t i m e t d( on) v dd = 0 v , r l = 1.5 ? i d ? - 10 a, v gen = - 4.5 v, r g = 1 ? 70 105 ns rise time t r 70 105 turn-off delay time t d( off) 45 68 fall time t f 27 41 tu r n - o n d e l ay t i m e t d( on) v dd = - 15 v, r l = 1 .5 ? i d ? - 10 a, v gen = - 10 v , r g = 1 ? 18 30 rise time t r 15 25 turn-off delay time t d( off) 52 80 fall time t f 14 25 drain -source body diode characteristics continuous source-drain diode current i s t c = 25 c - 5.8 a pulse diode forward current i sm - 60 body diode v oltage v sd i s = - 10 a, v gs = 0 v - 0.78 - 1.2 v body diode reverse recovery time t rr i f = - 10 a, di/ dt = 100 a/s, t j = 25 c 35 53 ns body diode reverse recovery charge q rr 25 38 nc reverse recovery fall time t a 19 ns re verse recovery rise time t b 16 dt 1 www. daysemi.jp
3 typica l characteristics (25 c, unless otherwise noted) gate c urrent vs. gate-source voltage output characteristics on-resistance vs. drain current 0.000 0.003 0.006 0.009 0.012 0.015 0 6 12 18 24 30 i gs s - gate current (ma) v gs - gate-source voltage (v) t j = 25 c 0 15 30 45 60 0 0.5 1 1.5 2 i d - drain current (a) v ds - drain-to-source voltage (v) v gs = 4 v v gs = 10 v thru 5 v v gs = 3 v 0.002 0.005 0.008 0.011 0.014 01 53 04 56 0 r ds( on) - on-resistance () i d - drain current (a) v gs = 6 v v gs = 4.5 v v gs = 10 v gate c urrent vs. gate-source voltage transfer characteristics capacitance 10 -0 2 10 -0 3 10 -0 4 10 -0 5 10 -0 6 10 -0 7 10 -0 8 10 -0 9 0 6 12 18 24 30 36 i gs s - gate current (a) v gs - gate-to-source voltage (v) t j = 150 c t j = 2 5 c 0 2 4 6 8 10 01234 i d - drain current (a) v gs - gate-to-source voltage (v) t c = 25 c t c = 125 c t c = - 55 c 0 1200 2400 3600 4800 6000 7200 0 6 12 18 24 30 c - capacitance (pf) v ds - drain-to-source voltage (v) c iss c os s c rs s dt 1 www. daysemi.jp
4 ty pical characteristics (25 c, unless otherwise noted) gate ch arge source-drain diode forward voltage threshold voltage 0 2 4 6 8 10 03 06 09 01 2 0 v gs - gate-to-source voltage (v) q g - total gate charge (nc) v ds = 24 v v ds = 7.5 v v ds = 1 5 v i d = 17.3 a 0.1 1 10 100 0.0 0.2 0.4 0.6 0.8 1.0 1.2 i s - source current (a) v sd - source-to-drain voltage (v) t j = 150 c t j = 2 5 c 1.1 1.45 1.8 2.15 2.5 - 50 - 25 0 25 50 75 100 125 150 v gs (th) (v ) t j -t emperature ( c) i d = 250 a on -resistance vs. junction temperature on-resistance vs. gate-to-source voltage single pulse power, junction-to-ambient 0.60 0.85 1.10 1.35 1.60 - 50 - 25 0 25 50 75 100 125 150 r ds( on) - on-resistance (normalized) t j - junction temperature ( c) i d = 13a v gs = 1 0 v v gs = 4.5 v 0.000 0.005 0.010 0.015 0.020 2468 1 0 r ds( on) - on-resistance () v gs - gate-to-source voltage (v) t j = 125 c t j = 2 5 c i d = 13 a 0 30 50 10 20 pow er (w ) t ime (s) 1 600 10 40 0.1 0.01 100 dt 1 www. daysemi.jp
5 typica l characteristics (25 c, unless otherwise noted) * th e power dissipation p d is based on t j( max.) = 15 0 c, using junction-to-cas e thermal resistance, and is mo re useful in settling the upper dissipation limit for cases where additional heatsinking is used. it is used to determine the current rating, when this rating falls below the package limit. safe operating area, junction-to-ambient power junction-to-foot 0.001 0.01 0.1 1 10 100 0.1 1 10 100 i d - drain current (a) v ds - drain-to-source voltage (v) * v gs > minimum v gs at which r ds( on) is specied 100 ms li mited by r ds( on) * 1 ms t a = 25 c single pulse bv dss limited 10 ms 100 s 1 s dc, 10 s 0 2.2 4.4 6.6 8.8 0 25 50 75 100 125 150 p ower (w) t c - case temperature ( c) curr ent derating* power junction-to-ambient 0 6 12 18 24 30 0 25 50 75 100 125 150 i d - drain current (a) t c - case temperature ( c) 0.0 0.5 0.9 1.4 1.8 0 25 50 75 100 125 150 p ower (w) t a - ambient temperature ( c) dt 1 www. daysemi.jp
6 ty pical characteristics (25 c, unless otherwise noted) norm alized thermal transient im pedance, junction-to-ambient 10 -3 10 -2 1 10 600 10 -1 10 -4 100 2 1 0.1 0.01 0.2 0.1 0.05 0.02 single pulse duty cycle = 0.5 square wave pulse duration (s) nor malized eff ective transient thermal impedance 1. duty cycle, d = 2. per unit base = r th ja = 90 c/w 3. t jm - t a = p dm z th ja (t) t 1 t 2 t 1 t 2 notes: 4. surface mounted p dm no rmalized thermal transient impedance, junction-to-foot 10 -3 10 -2 10 10 -1 10 -4 2 1 0.1 0.01 0.2 0.1 0.05 0.02 single pulse duty cycle = 0.5 square wave pulse duration (s) normalized ef fective transient thermal impedance 1 dt 1 www. daysemi.jp
1 power pak so-8, (single/dual) millimeters inches dim. min. nom. max. min. nom. max. a 0.97 1.04 1.12 0.038 0.041 0.044 a1 0.00 - 0.05 0.000 - 0.002 b 0.33 0.41 0.51 0.013 0.016 0.020 c 0.23 0.28 0.33 0.009 0.011 0.013 d 5.05 5.15 5.26 0.199 0.203 0.207 d1 4.80 4.90 5.00 0.189 0.193 0.197 d2 3.56 3.76 3.91 0.140 0.148 0.154 d3 1.32 1.50 1.68 0.052 0.059 0.066 d4 0.57 typ. 0.0225 typ. d5 3.98 typ. 0.157 typ. e 6.05 6.15 6.25 0.238 0.242 0.246 e1 5.79 5.89 5.99 0.228 0.232 0.236 e2 3.48 3.66 3.84 0.137 0.144 0.151 e3 3.68 3.78 3.91 0.145 0.149 0.154 e4 0.75 typ. 0.030 typ. e 1.27 bsc 0.050 bsc k 1.27 typ. 0.050 typ. k1 0.56 - - 0.022 - - h 0.51 0.61 0.71 0.020 0.024 0.028 l 0.51 0.61 0.71 0.020 0.024 0.028 l1 0.06 0.13 0.20 0.002 0.005 0.008 0 - 12 0 - 12 w 0.15 0.25 0.36 0.006 0.010 0.014 m 0.125 typ. 0.005 typ. ecn: t10-0055-rev. j, 15-feb-10 dwg: 5881 3. dimensions e xclusive of mold flash and cutting burrs. 1. notes 2 inch will go vern. dimensions exclusive of mold gate burrs. bac kside view of single pad backside view of dual pad detail z d d1 d2 c a e1 d1 e2 d2 e b 1 2 3 4 h 4 3 2 1 1 2 3 4 b l d2 d3(2x) z a1 k1 k d e w l1 d5 e3 d4 e4 e4 k l h e2 d4 d5 m e3 0.150 0.008 2 2 package information
legal disclaimer notice www. daysemi.jp 1 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. din-tek intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, din-tek ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. din-tek makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, din-tek disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on din-tek s knowledge of typical requirements that are often placed on din-tek products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify din-tek s terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, din-tek products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the din-tek product could result in personal injury or death. customers using or selling din-tek products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized din-tek personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of din-tek . product names and markings noted herein may be trad emarks of their respective owners. material category policy din-tek intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some din-tek documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. din-tek intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some din-tek documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards. legal disclaimer notice www.daysemi.jp revision: 02-oct-12 1 document number: 72610 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. din-tek intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, din-tek ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. din-tek makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, din-tek disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on din-tek s knowledge of typical requirements that are often placed on din-tek products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify din-tek s terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, din-tek products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the din-tek product could result in personal injury or death. customers using or selling din-tek products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized din-tek personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of din-tek . product names and markings noted herein may be trad emarks of their respective owners. material category policy din-tek intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some din-tek documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. din-tek intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some din-tek documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
